Zigbee Configurable Firmware v2.5

Yes i’m sure look :

i read the Zigbee cluster: ZCL_CLUSTER_ID_GEN_ON_OFF Zigbee attribute: ATTRID_ON_OFF and this is the result (the endpoint 2 is off so this is the starting status)

[ZB msg] len: 28 cmd0: 44 cmd1: 81 data: 0 0 6 0 BE B9 2 1 0 60 0 92 B3 7 0 0 8 18 5 1 0 0 0 10 0 BE B9 1D
zigbee_cmd : 0x4481
AF_INCOMING_MSG
group_id: 0
cluster_id: 6
src_addr: B9BE
src_endpoint: 2
dst_endpoint: 1
was_broadcast: 0
link_quality: 60
security_use: 0
time_stamp: 7B392
trans_seq_num: 0
len: 8
data: 18 5 1 0 0 0 10 0
cluster_id : 6
ZCL_CLUSTER_ID_GEN_ON_OFF
0

now i toggle it sending 0x02 to ZCL_CLUSTER_ID_GEN_ON_OFF endoint 2 (the lamp is on) and the device send the status immediately and is this :

[ZB msg] len: 25 cmd0: 44 cmd1: 81 data: 0 0 6 0 BE B9 2 1 0 60 0 A2 A2 A 0 0 5 18 6 B 2 0 BE B9 1D
zigbee_cmd : 0x4481
AF_INCOMING_MSG
group_id: 0
cluster_id: 6
src_addr: B9BE
src_endpoint: 2
dst_endpoint: 1
was_broadcast: 0
link_quality: 60
security_use: 0
time_stamp: AA2A2
trans_seq_num: 0
len: 5
data: 18 6 B 2 0
cluster_id : 6
ZCL_CLUSTER_ID_GEN_ON_OFF
0

but if i read the attribute ATTRID_ON_OFF the result is this (that is correct becaus is ON)

[ZB msg] len: 28 cmd0: 44 cmd1: 81 data: 0 0 6 0 BE B9 2 1 0 60 0 71 26 E 0 0 8 18 7 1 0 0 0 10 1 BE B9 1D
zigbee_cmd : 0x4481
AF_INCOMING_MSG
group_id: 0
cluster_id: 6
src_addr: B9BE
src_endpoint: 2
dst_endpoint: 1
was_broadcast: 0
link_quality: 60
security_use: 0
time_stamp: E2671
trans_seq_num: 0
len: 8
data: 18 7 1 0 0 0 10 1
cluster_id : 6
ZCL_CLUSTER_ID_GEN_ON_OFF
1

If i push the button linked to the output, the device send immediately the status but is always correct (0 if is off and 1 if is on).

About the reset, the problem is when i must release the button because i can’t count 10 seconds 🙂 a need a visual information i don’t know blink rapidly the led so i know that the the device is resetting

Hello, i’m using this function to get the basic cluster ox0000 infornation :

uint8_t st_buffer[3] = { /* Frame control */ 0x00, // Command is global
/* Transaction Sequence Number */0x00, /* control_switch_cmd_seq++ */
/* Value Control */ 0x0000 /* command identifier read attribute */
};
st_buffer[1] = control_switch_cmd_seq++;

af_data_request_t st_af_data_request;
st_af_data_request.cluster_id = 0x00;
st_af_data_request.dst_address = new_switch_address;
st_af_data_request.dst_endpoint = 0x01;
st_af_data_request.src_endpoint = 0x01;
st_af_data_request.trans_id = 0x00;
st_af_data_request.options = 0x10;
st_af_data_request.radius = 0x0F;
st_af_data_request.len = sizeof(st_buffer);
st_af_data_request.data = st_buffer;
zigbee_network.send_af_data_req(st_af_data_request);
}

but i can’t get the informations that i set in the expert tab.

I would to get manufacturerid, manufacturer name and model name but return only 3 bytes.

Can you help me to understand what i’m doing wrong please?

Thank you in advance for you help.

Best regards,
Antonio.

Hello,

So how i must configure Input 1 ih the gui of your program to start join when i long press the button connected to the pin that i indicate in the input 1 configuration ?

Now i checked Input 1 P00 GPIO External pull down (because i use a touch button that is active high).

It’s enought? or i must configure other parameters of Input 1 in the gui of your program?

Best regards.

Antonio.

yes that’s right i want to control my RGB channels by PWM….

Thanks,
will give it a go.

Many thanks for responding. Looks like I used an capital i (for Input) rather than a lower case L.

In MQTT.fx I subscribed to both zigbee2mqtt/Solar S0 Counter/# and zigbee2mqtt/Solar S0 Counter and both worked.

I find that the CC2530 device is constantly sending 3 outputs every second even though the “Default reporting period” is not set. Looking at the zigbee2mqtt log I can see it receives a message for each of the defined 3 GPIO pins. Here is an extract:

cluster ‘genOnOff’, data ‘{“onOff”:0}’ from endpoint 1 with groupID 0
cluster ‘genAnalogInput’, data ‘{“presentValue”:0}’ from endpoint 1 with groupID 0
cluster ‘genAnalogInput’, data ‘{“presentValue”:28,”description”:”C”}’ from endpoint 2 with groupID 0

For each of these zigbee2mqtt then publishes on Solar S0 Counter (extract):
‘{“state_bottom_left”:”OFF”,”linkquality”:99,”state_bottom_right”:”OFF”,”l1″:0,”l2″:28,”temperature”:28,
‘{“state_bottom_left”:”OFF”,”linkquality”:99,”state_bottom_right”:”OFF”,”l1″:0,”l2″:28,”temperature”:28,
‘{“state_bottom_left”:”OFF”,”linkquality”:102,”state_bottom_right”:”OFF”,”l1″:0,”l2″:28,”temperature”:28,

I.e. each output message is a complete list of the 3 pins (“OFF” which I guess is Output 1, and I1 (counter) and I2 (temperature).

I could live with this but the constant high frequency output is worrying. I thought that if “Default reporting period” is not set then I should only get output when requested. Or have I misunderstood?

I then tried to issue a get command, first to I2 for the temperature. In MQTT.fx I Published to zigbee2mqtt/Solar S0 Counter/get/l2 with payload 1 but there was no response. The zigbee2mqtt log says:

debug 2020-07-02 21:43:39: Received MQTT message on ‘zigbee2mqtt/Solar S0 Counter/get/l2’ with data ‘1’
debug 2020-07-02 21:43:39: Publishing get ‘get’ ‘l2’ to ‘Solar S0 Counter’

When I issued a get command to I1 (the counter which is not currently connected to any circuit): zigbee2mqtt/Solar S0 Counter/get/l1 with payload 1 the zigbee2mqtt log reports an error:

debug 2020-07-02 21:57:49: Received MQTT message on ‘zigbee2mqtt/Solar S0 Counter/get/l1’ with data ‘1’
debug 2020-07-02 21:57:49: Publishing get ‘get’ ‘l1’ to ‘Solar S0 Counter’
debug 2020-07-02 21:57:49: Received Zigbee message from ‘Solar S0 Counter’, type ‘raw’, cluster ‘genAnalogInput’, data ‘{“type”:”Buffer”,”data”:[24,38,1,85,0,0,57,0,0,0,0,28,0,0,66]}’ from endpoint 1 with groupID 0
debug 2020-07-02 21:57:49: No converter available for ‘ptvo.switch’ with cluster ‘genAnalogInput’ and type ‘raw’ and data ‘{“type”:”Buffer”,”data”:[24,38,1,85,0,0,57,0,0,0,0,28,0,0,66]}’
……. repeats previous debug lines x2……….
debug 2020-07-02 21:58:02: No converter available for ‘ptvo.switch’ with cluster ‘genAnalogInput’ and type ‘raw’ and data ‘{“type”:”Buffer”,”data”:[24,38,1,85,0,0,57,0,0,0,0,28,0,0,66]}’
error 2020-07-02 21:58:12: Publish ‘get’ ‘l1’ to ‘Solar S0 Counter’ failed: ‘Error: Read 0x00124b001f2857e3/1 genAnalogInput([“presentValue”,”description”], {“timeout”:10000,”manufacturerCode”:null,”disableDefaultResponse”:true}) failed (Error: Timeout – 33246 – 1 – 38 – 12 – 1 after 10000ms)’
debug 2020-07-02 21:58:12: Error: Read 0x00124b001f2857e3/1 genAnalogInput([“presentValue”,”description”], {“timeout”:10000,”manufacturerCode”:null,”disableDefaultResponse”:true}) failed (Error: Timeout – 33246 – 1 – 38 – 12 – 1 after
10000ms) at Endpoint. (/app/node_modules/zigbee-herdsman/dist/controller/model/endpoint.js:182:23)
at Generator.throw ()
at rejected (/app/node_modules/zigbee-herdsman/dist/controller/model/endpoint.js:6:65)

Have you any ideas, please?

Alan

Hi, how could we help/contribute to get the power save mode prioritized? Thx and greets Dieter

I tried to connect via zigbee2mqtt, the statuses work well, both from the button and from the control system. But now I have 5 switches for one relay, of which 4 do not work =)) Please tell me, for which control system was this configurator developed? What should devices be used with so that they work well? https://take.ms/m4BsV

here you are:
https://client23.12hp.de/tmp/Zwischenablage01.jpg

P00 and P02 behave identically regarding logic: both active low.
I tried also P00/P02 configured as tristate and internal pull-down. Same result.

Best regards, O