CC2530 + CC2590/CC2591/CC2592/RFX2401 routers

Nowadays, some manufacturers offer boards with additional power amplifiers for the radio signal. These boards may cover a rather large area than the regular CC2530. The standard router firmware does not work with these boards.

Example: EBYTE E18-MS1PA1-IPX

Therefore I’ve prepared particular versions:

https://ptvo.info/wp-content/uploads/2018/09/cc2530_cc2590_1.2.2a.44539_firmware.zip
https://ptvo.info/wp-content/uploads/2018/09/cc2530_cc2591_1.2.2a.44539_firmware.zip
https://ptvo.info/wp-content/uploads/2018/09/cc2530_cc2592_1.2.2a.44539_firmware.zip

The RFX2401 power amplifier has wiring identical to CC2590. Please, use the firmware for cc2530 + cc2590.

Your comments are welcome!

Notes:

  1. These boards require a power supply with stable high output current (500mA). Double check cheap Chinese power sources.
  2. Double check the distance between pins or pin pads. For example, EBYTE board has 1.27 mm between pins. It is very hard to solder.

Comments
Harvey Specter
Posted at 01:03 May 13, 2019
Jed anderson
Reply
Author

Hello I got some of the  E18-MS1PA1-IPX
…I have some questions:

1.- to flash the firmware… I must use : pin1 ground, pin2 vcc, pin3 p.2.2, pin4 p.2.1 and p24 reset? (In some other tutorials they use a second vcc conection but this modules only have pin2 as vcc)

2.- do you know some breakout board for this modules?

Best regards
Jed

    Harvey Specter
    Posted at 04:02 May 13, 2019
    Owner
    Reply
    Author

    Hello,

    1. Yes, correct. I’ve only used these pins (pin1-pin4, pin24).
    2. No, I don’t know. I’ve soldered thin wires directly to the module.

Harvey Specter
Posted at 15:26 July 11, 2019
Thomas
Reply
Author

Hello!

How much of an improvement of coverage is possible with these in comparison to a CC2531, a CC2530 and a CC2530+CC2591 with external Antenna?
Also has anyone tried an EBYTE E18-2G4Z27SI which is advertised with 500 mW and up to 2.5 km?

    Harvey Specter
    Posted at 12:34 July 13, 2019
    Owner
    Reply
    Author

    CC2530+CC2591 with external Antenna works much better. It replaced 3 cc2531 routers in my home. I think, 500mW is a fake, because it has the similar schematic as CC2530+CC2591. If you’ll find a data sheet for the power amplifier, you can see 100 mW output power.

      Harvey Specter
      Posted at 01:49 July 14, 2019
      Thomas
      Reply
      Author

      Thank you!

      How would you rate the CC2591 in comparison to the CC2592?
      After a CC2531 with PCB-antenna and a CC2530 with external antenna I now have a WeBee board with CC2530+CC2591, but I’m a little disappointed with the increase in the reported linkquality values from the Aqara sensors. Would it be worth it to order an EBYTE E18-MS1PA1-IPX?

        Harvey Specter
        Posted at 04:41 July 15, 2019
        Owner
        Reply
        Author

        I have boards with CC2591 and CC2592. I didn’t find any visible differences in my setup. I’m not sure that EBYTE E18-MS1PA1-IPX will help.

Harvey Specter
Posted at 20:51 August 20, 2019
Yeison
Reply
Author

Hello!

I tried to look into your differents posts and attaches files and I was not able to find the firmware called “CC2530ZNP-Pro-Secure_LinkKeyJoin_RXF2401.hex”

I have a GB2530 with a CC2530 + RFX2401, I am using the develop board from GBAN.

Do you know where I can find it?

Thanks!

    Harvey Specter
    Posted at 05:08 August 21, 2019
    Owner
    Reply
    Author

    You need firmware for a coordinator. I have firmware for routers only.

Harvey Specter
Posted at 23:48 October 19, 2019
talondnb
Reply
Author

I have a GBAN stick I’m using as a router. Can you suggest the best firmware for this? Also using another as the coordinator and similar situation, my home has long so requires this on both ends.

Thanks.

    Harvey Specter
    Posted at 06:51 October 22, 2019
    Owner
    Reply
    Author

    What chips does this stick have inside?

Harvey Specter
Posted at 08:11 December 5, 2019
Inverted
Reply
Author

Good news ptvo switch now recognised in domoticz plug-in 🙂
https://github.com/stas-demydiuk/domoticz-zigbee2mqtt-plugin

    Harvey Specter
    Posted at 08:41 December 5, 2019
    Owner
    Reply
    Author

    Thank you!

Harvey Specter
Posted at 05:16 April 17, 2020
Scott
Reply
Author

Do these firmwares change the assigned tx power at all or do they leave it as the default 0dB? If it’s the latter, any chance of some variants that set the transmit power higher for those boards that are capable?

    Harvey Specter
    Posted at 08:25 April 17, 2020
    Owner
    Reply
    Author

    It sets the maximum TX power.

      Harvey Specter
      Posted at 15:50 April 17, 2020
      Scott
      Reply
      Author

      Great! I’d hoped so given your power supply comment, but I wanted to confirm. Thank you for all your work to make this stuff possible.

Harvey Specter
Posted at 15:58 April 17, 2020
Giovanni C
Reply
Author

Thansk I will test this firmware! But I’ve a couple of questions:
1) how can I put the router in pairing mode? maybe first time usage it will be automatic but what if I need to re-pair it for any given reason?
2) does your firmware support a status LED? if YES to which GPIO shoudl be connected and how?

thanks!

    Harvey Specter
    Posted at 08:36 April 18, 2020
    Owner
    Reply
    Author

    1. Please, look at the readme.txt file for options
    2. The standard firmware supports the led pin for CC2531 only. My customizable firmware can work as a router and allows configuring the led pin number.

      Harvey Specter
      Posted at 11:09 April 18, 2020
      Giovanni C
      Reply
      Author

      Thanks, I missed to read readme.txt indeed, my bad!!!
      About the firmware you mean that this one does not have LED support, so I need to use your 2.2V Firmware (https://ptvo.info/zigbee-switch-configurable-firmware-v2-210/) disabling all input/output and keeping only the status LED enabled?

        Harvey Specter
        Posted at 11:36 April 18, 2020
        Owner
        Reply
        Author

        Yes, exactly.

          Harvey Specter
          Posted at 13:39 April 18, 2020
          Giovanni C
          Author

          Thanks, just tried it and it seems zigbee2mqtt cannot find information for the device with your custom firmware 🙁
          How the support can be added ?

          Harvey Specter
          Posted at 13:43 April 18, 2020
          Owner
          Author

          Z2M has support for all my firmwares.

          Harvey Specter
          Posted at 13:47 April 18, 2020
          Giovanni C
          Author

          normal version or I should ude the “DEV” one?
          I just tried again with both my Home Assistant istance and test zigbee rig I do have and yes the device is recognised as router but it shows no data and does not report anythign (like Linkquality for example)

          Harvey Specter
          Posted at 13:50 April 18, 2020
          Owner
          Author

          You need the ‘dev’ version.

          Harvey Specter
          Posted at 13:56 April 18, 2020
          Giovanni C
          Author

          ah OK that’s the issue then! thanks I will move my test environemnt to the DEV version

Leave a Reply to talondnb
Cancel Reply