LED

If the LED pin is configured.

  • Short, fast blinks (one per second) – the router is connecting to a network.
  • Short, long blinks (one per 4 seconds) – normal operations.
  • Three short blinks – the router cannot send a report to a coordinator.

Pairing

Flash firmware and permit joining to a network on your coordinator. The firmware starts a join procedure automatically.

The end device or router firmware tries to connect to a network for 30 minutes. If all attempts failed, the firmware pauses searching for 15 minutes.

The firmware with power saving tries to connect for 1 minute and after the unsuccessful attempt goes to the deep sleep mode. You can prolong the joining cycle by clicking the GPIO button or “External wake-up” configured on “Input 1” (see GPIO).

CC2652 or CC1352: sometimes, you should additionally reset your device to factory defaults after flashing.

Re-pairing or reset to factory defaults

Power on, wait 2 seconds, power off, repeat this cycle three times.

If you configured the GPIO or “External wake-up” button on “Input 1”, click and hold the button for 10 seconds. The “Switch” mode for that button should be off.


Comments
Harvey Specter
Posted at 13:16 March 15, 2024
Julian
Reply
Author

Hi! Thank you for your software.
I couldn’t find this information anywhere. Is the status LED configured with an internal pullup resistor? Or does it need an external resistor in addition to the LED?
I’m trying to figure out what’s the minimum circuit I need, and I want to know if it will be OK if I connect the LED directly from the status LED GPIO pin to ground without any resistor.
Thanks!

    Harvey Specter
    Posted at 09:46 March 19, 2024
    Owner
    Reply
    Author

    The firmware uses the internal pull-up resistor.

Harvey Specter
Posted at 08:49 March 7, 2024
Oleg
Reply
Author

Hallo. I have question – here i make ptvo zigbee device, but smarthome application with wifi|zgbee|bl gateway (tuya/moes…) don’t see it. is it possible or only DIY getaway as SLS can connect with ptvo firmware? pleasee
p.s. when in mobile application i press “add device” my pvto device blink 0ne per 4 sec for connecting/ but no devices appear in app

    Harvey Specter
    Posted at 10:53 March 11, 2024
    Owner
    Reply
    Author

    Tuya/Moes hubs with stock firmware do not accept 3rd party devices, and DIY too.

Harvey Specter
Posted at 17:41 May 2, 2023
alainvtr
Reply
Author

hi !
what is the changelog for the 2023-02-07 and 2023-04-22 versions ?
thx.

Harvey Specter
Posted at 16:16 October 31, 2022
alainvtr
Reply
Author

hi !
with the “external wake up” wich value should i use for “bind command” ?
if a simple button is used on a PIN, i suppose i’ve to choose “pull-up” ?

    Harvey Specter
    Posted at 03:46 November 1, 2022
    Owner
    Reply
    Author

    The “external wake up” pin does not send commands to a bound device. It just wakes up the device, and it sends the regular periodic report.

Harvey Specter
Posted at 21:11 October 18, 2021
glcos
Reply
Author

In case of RF-STAR module RF-BM-2652P2 the chip INPUT 1 is not exposed outside and is in fact not available. How do I implement the pairing button in that module ?

    Harvey Specter
    Posted at 03:33 October 19, 2021
    Owner
    Reply
    Author

    Please note that you should define a logical “Input 1” in the configuration, but you can assign any physical pin.

    Harvey Specter
    Posted at 16:12 November 1, 2022
    alainvtr
    Reply
    Author

    my purpose is the “external wake up” on PIN1 to force à pairing – so i’ve only to choose a “pull-up” ?

      Harvey Specter
      Posted at 03:23 November 2, 2022
      Owner
      Reply
      Author

      The pull resistor type depends on your schematic. In most cases, the internal pull-up resistor is enough.

Harvey Specter
Posted at 13:19 February 28, 2021
fred
Reply
Author

Hello,
Suggestion/Wish:
Add an option to disable repairing using “Power on, wait 2 seconds, power off, repeat this cycle three times.”.
I had to repair my 3 devices after a power outage.
Thanks.

    Harvey Specter
    Posted at 14:33 February 28, 2021
    Owner
    Reply
    Author

    Hello,
    Hmmm. It is a strange or rare power outage with this scenario.

Leave a Reply to Owner
Cancel Reply